*NEW*Temporary Protected Lighting(TPL®)
- Rough Service with watertight IP68 lens rating
- Designed for indoor and outdoor applications
- Daisy chain up to 250m
- Can be manufactured to end user’s specifications
- AS/NZ 60598.2.20 compliant
- High impact polycarbonate lens
- Custom lengths available
- Engineered and made in New Zealand
LG15.HOOK CABLE HOOK PACK 25
- Multi-purpose, non-conducting, plastic lead hook
- Versatile design fits over doors, walls, scaffold and almost anything
- Holds up to 8 leads and up to 50mm cables
3 Way Splitter
3k3 125E/*M – *indicates length of cable
Interlocking Cable Protectors
Protecting electrical cable from traffic can be a serious problem. Use of our interlocking rubber cable ramps provides mechanical protection from falling weights and most vehicle types, of weights up to 3 tonne.
A total length may be attained by simply snapping the JIGSAW type interconnections together on the individual ramps. Cable ramps have top hinged lids for easy access and provide extra safety with their anti skid design. Cable ramps are available in straight and corner units.
Earth Screened Cables
Realizes High-Speed Advanced Machine Control
Three phase Lifeguard leads are available in 32A, 63A, and 125A current ratings and built with standard lengths of 10m, 20m and 30m. Non standard lengths can however be made upon request.
The copper braided screen provides protection for the 4cores and acts as the earth providing maximum safety for personal.
5pin IP67 rated connectors complying with IEC60309 are fitted at each end of the lead. Single phase earth screen cable is also available in 2.5mm or 6.0mm for use with 15A, 16A or 32A connectors.
Lifeguard leads have been designed for use on construction sites and are suitable for interconnection of the Lifeguard power reticulation system.
Complies with ASNZS 3012 Appendix K
600/1000V (6 – 35mm²)
The LIFEGUARD 37 Wall Supply Module is available for single phase electrical systems from 10A flat pin to 32A round pin lEC309 type outlets. This equipment is fitted with an RCD (Residual Current Device), over current and short circuit protection. The LIFEGUARD 37 series has been specifically designed to provide protection against electrocution for personnel using electrical machinery.
The LIFEGUARD 37 enclosure is manufactured from high impact polycarbonate which is resistant to corrosion and is suitable for harsh enviroments, ie. paper and steel manufacturing and marine.
- • Power on indication
- • MCB only protection
- • Choice of colour (quantity dependent)
- • 110V – 240V Socket Selection
- • Freestanding pillar option also available (pictured left)
The LIFEGUARD 34 system has a generous sized enclosure designed for installation directly onto larger Gensets. These units may be fitted with a range of multi-voltage and multi-amperage sockets with the appropriately rated RCDs and MCBs.
The LIFEGUARD 34 system has a maximum capacity of 250A and can be designed with many combinations of socket outlets, up to and including 125A. It is manufactured with cable tie bars for protection of leads supplied from this LIFEGUARD.
Expansion and Flexibility
LIFEGUARD 34 units can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and an extensive range of socket outlets.
The LIFEGUARD 34 enclosures are also adaptable for a large range of other applications including: housing sensors, control components and other electronic equipment, particularly in its harsh environment.
The LIFEGUARD 33B system is a generously sized GRP enclosure designed for installation of higher amperage fittings, larger MCCBs, RCDs and socket outlets.
LIFEGUARD 33B units allow for termination of larger supply cables, in excess of 25mm. Sometimes these will be rigid steel wire armoured and may loop inside the LIFEGUARD® and onto other supply outlets.
LIFEGUARD 33B unit is in an enclosure with a moulded lid to accommodate requirements of multi-voltage and multi-amperage sockets to service the demands of many industrial work areas. Often used in areas where many variations may be necessary, especially take-off points for larger generators.
Expansion and Flexibility
LIFEGUARD 33B can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and a wide range of socket outlets. They can be manufactured with cable tie bars for protection of leads supplied from this LIFEGUARD.
The LIFEGUARD 33B enclosures are adaptable for a wide range of other applications including: housing sensors, control components and other electronic equipment, particularly in harsh environments.
LIFEGUARD 26B Wall Supply Modules are available for both single, three phase and combination electrical systems. The equipment is fitted with an RCD which is specifically designed to provide protection against electrocution for personnel using electrical equipment.
LIFEGUARD 26B series can handle current as low as 10A through to 125A, in a wide range of pin configurations. The enclosure is manufactured from GRP which is extremely resistant to corrosion and is especially suitable for harsh environments, both indoors and outdoors. All internal wiring is complete to terminals for the incoming cables and the unit is bench tested and given the relevant current warrant of fitness. The RCDs in the LIFEGUARD 26B units keep the use of electrical equipment within health and safety guidelines.
Expansion and Flexibility
LIFEGUARD 26B units can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and a wide range of socket outlets.
The LIFEGUARD 26B enclosures are adaptable for a wide range of other applications including: housing sensors, control components and other electronic equipment, particularly in harsh environments.