Archives

LIFEGUARD® 37

LIFEGUARD® 37

The LIFEGUARD 37 Wall Supply Module is available for single phase electrical systems from 10A flat pin to 32A round pin lEC309 type outlets. This equipment is fitted with an RCD (Residual Current Device), over current and short circuit protection. The LIFEGUARD 37 series has been specifically designed to provide protection against electrocution for personnel using electrical machinery.

The LIFEGUARD 37 enclosure is manufactured from high impact polycarbonate which is resistant to corrosion and is suitable for harsh enviroments, ie. paper and steel manufacturing and marine.

Options Include:
  • • Power on indication
  • • MCB only protection
  • • Choice of colour (quantity dependent)
  • • 110V – 240V Socket Selection
  • • Freestanding pillar option also available (pictured left)

Lifeguard 37

Product Enquiry

    Lifeguard 37

    LIFEGUARD® 34

    LIFEGUARD® 34

    The LIFEGUARD 34 system has a generous sized enclosure designed for installation directly onto larger Gensets. These units may be fitted with a range of multi-voltage and multi-amperage sockets with the appropriately rated RCDs and MCBs.

    The LIFEGUARD 34 system has a maximum capacity of 250A and can be designed with many combinations of socket outlets, up to and including 125A. It is manufactured with cable tie bars for protection of leads supplied from this LIFEGUARD.

    Expansion and Flexibility

    LIFEGUARD 34 units can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and an extensive range of socket outlets.

    The LIFEGUARD 34 enclosures are also adaptable for a large range of other applications including: housing sensors, control components and other electronic equipment, particularly in its harsh environment.

    Lifeguard 34
    Lifeguard 34

    Lifeguard 34

    Product Enquiry

      Lifeguard 34

      LIFEGUARD® 33B

      LIFEGUARD® 33B

      The LIFEGUARD 33B system is a generously sized GRP enclosure designed for installation of higher amperage fittings, larger MCCBs, RCDs and socket outlets.

      LIFEGUARD 33B units allow for termination of larger supply cables, in excess of 25mm. Sometimes these will be rigid steel wire armoured and may loop inside the LIFEGUARD® and onto other supply outlets.

      LIFEGUARD 33B unit is in an enclosure with a moulded lid to accommodate requirements of multi-voltage and multi-amperage sockets to service the demands of many industrial work areas. Often used in areas where many variations may be necessary, especially take-off points for larger generators.

      Expansion and Flexibility

      LIFEGUARD 33B can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and a wide range of socket outlets. They can be manufactured with cable tie bars for protection of leads supplied from this LIFEGUARD.

      The LIFEGUARD 33B enclosures are adaptable for a wide range of other applications including: housing sensors, control components and other electronic equipment, particularly in harsh environments.

      Lifeguard 33B
      Lifeguard 33B

      Lifeguard 33B

      Product Enquiry

        Lifeguard 33B

        LIFEGUARD® 26B

        LIFEGUARD® 26B

        LIFEGUARD 26B Wall Supply Modules are available for both single, three phase and combination electrical systems. The equipment is fitted with an RCD which is specifically designed to provide protection against electrocution for personnel using electrical equipment.

        LIFEGUARD 26B series can handle current as low as 10A through to 125A, in a wide range of pin configurations. The enclosure is manufactured from GRP which is extremely resistant to corrosion and is especially suitable for harsh environments, both indoors and outdoors. All internal wiring is complete to terminals for the incoming cables and the unit is bench tested and given the relevant current warrant of fitness. The RCDs in the LIFEGUARD 26B units keep the use of electrical equipment within health and safety guidelines.

        Expansion and Flexibility

        LIFEGUARD 26B units can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and a wide range of socket outlets.

        The LIFEGUARD 26B enclosures are adaptable for a wide range of other applications including: housing sensors, control components and other electronic equipment, particularly in harsh environments.

        Lifeguard 26B
        Lifeguard 26B

        Lifeguard 26B

        Product Enquiry

          Lifeguard 26B

          LIFEGUARD® 20B

          LIFEGUARD® 20B

          LIFEGUARD 20B wall supply modules are available for both single and three phase electrical systems. The unit is manufactured to utilise situations where one RCD protected socket outlet is required and mounting space is limited. The RCD is fitted to provide protection against electrocution in accordance with OSH guidelines.

          The LIFEGUARD 20B series has a current capability ranging from 10A to 32A in a wide range of pin configurations. The enclosure is manufactured from GRP which is extremely suitable for harsh environments, both indoors and outdoors. LIFEGUARD® 20Bs can be built to suit customers specific socket requirements. All internal wiring is complete to terminals for the incoming cables. After bench testing the units are given a current warrant of fitness.

          Expansion and Flexibility

          The LIFEGUARD 20B system can be fitted with RCDs up to 100 mA ratings for machine protection. They can also be fitted with MCCB protection and a wide range of socket outlets.

          LIFEGUARD 20B enclosures are adaptable for a wide range of other applications including: housing sensors, control components and other electronic equipment, particularly in harsh environments.

          Lifeguard 20B
          Lifeguard 20B

          Lifeguard 20B

          Product Enquiry

            Lifeguard 20B

            LIFEGUARD® 15

            LIFEGUARD® 15

            Site Hut Connection

            The LIFEGUARD  15 is a low cost and convenient method of interconnecting site huts, portacoms, offices, toilet blocks, container workshops and stores.

            By eliminating the need for point of entry boxes, non tradesmen can simply plug the huts together. As the units are compatible with the LIFEGUARD system, a standard LIFEGUARD 16 cable is used. Your site electrical system arrangements are made easy.

            Lifeguard 15
            Lifeguard 15

            Lifeguard 15

            Product Enquiry